Sunday, May 4, 2014

Status of QEG Build Morocco: Build Day 9 - Additional Capacitors Arrive: Comments from an Engineer

Photos by Julian Robles
We had one of the independent engineers that was here for the build leave a comment on Status of QEG Build Morocco: Build Day 3 - Initial Resonance Achieved! (Video), with some updates about the QEG. This commentary is relevant to the build and we thought we would share it. Thanks for commenting!

A quick update on this "from the ground". I have been in Morocco building the QEG for the past 10 days, and arrived home yesterday.

I am an engineer and am independent of the QEG group. I went out to Morocco to be involved in the QEG build and to make independent 3rd party measurements. As suggested by Justin & Julian's comments, this video represents only the first step in truly testing the claims of the QEG - it was the first time it was turned on, and was completely un-tuned. We measured this un-tuned set-up using voltage/current probes on an oscilloscope and showed about 1000W power from the wall, and 350W across the load (in this case 3 x 100W bulbs), so a COP (co-efficiency of performance) of about 35%. This was a few days ago, and in this set-up we would not expect a COP greater than than 100% even when tuned because the circuit is not complete.




Getting readings on the oscilloscope

As of yesterday, the final parts arrived to tune the system (capacitors), and it will take a few days to complete that process. In addition to the set-up shown in this video, the 'exciter circuit' has been added, which Witts says is the important aspect for creating the over-unity effect. The tuning will attempt to match the LC tank resonance to the mechanical resonance of the core (around 400Hz). Then the exciter circuit will create a regular 1.3MHz pulse to "condition" the core and apparently allow over-unity to take place.




'exciter coil'
Should over-unity be measured, the final part of the plan is to extract some of the excess generated power on the output side and loop it back into the input (the variac & motor), meaning the mains cable can be unplugged. 

However, there is some work to do before this stage is reached. We have been spending a lot of time trying to understand the Witts work, and there are a few gaps in our knowledge that we are trying to figure out. I plan to go back out there in a few days to continue the assessment. The QEG team (Jamie, Val & Hope) are the most genuine, selfless and lovely people I have ever met. I would ask that you all have some patience with this. The right people are there to make this happen, just hold the space open to allow this to come about. 

- Mr. Jalapeno

The Capacitors have been in the QEG shop since build day 8, May 3rd, and the team has been at work since then preparing for the next round of testing. Stay tuned for more updates and as the Engineer suggested, hold the space of love and patience as we step forward into our collective future. 
- Justin and Julian

More Photos:




19 comments :

  1. Thank you Justin and Julian for continuing to ask the hard questions and take the clear photos that allow us to follow the progress of this historic journey. I posted your link on my site and have encouraged my readers to do the same. I want to express my appreciation to both of you. Blessings ♥

    ReplyDelete
  2. Great update! Re-posted on my blog. Thanks!
    with gratitude - tomas

    ReplyDelete
  3. Thank you for the update
    Am sending positive energy and success to our goal

    ReplyDelete
  4. Looks like you guys are forging ahead, great progress! Thanks for the update!

    ReplyDelete
  5. Thank you for the work you do. We really hope this could be it. We made a song about this theme: https://www.youtube.com/watch?v=JBlypLHh5zc Enjoy!

    ReplyDelete
  6. Following this new adventure from end of april and am very excited to see how it all evolves. Especially the 'foor the people' thought makes this journey worth while!
    This needs our attention and spiritual focus then it will happen ...

    ReplyDelete
  7. Thank you!
    Now we know there is no over unity!
    Keep up the great work!

    ReplyDelete
  8. OK well let's see the over unity happen. Whatever your results are, positive or negative, I hope you do the honest scientific them and share them.

    ReplyDelete
  9. I have noticed something. May mean nothing at all... or may mean something very important.
    In the Witts video's showing their QEG running including self-running and powering a load... There is NO EXCITER COIL anywhere in sight. In one of them, the guy with the camera looks up close all the way around the machine to show all the wires and parts, and NO EXCITER COIL!!!??!!!?
    Where did first mention of this exciter coil come from? And why is it so needed for all the replications if not for the original??

    ReplyDelete
    Replies
    1. from my understanding, Jamie is using the exciter coil now to boost the power output. Right now Jamie has been spending a lot of time working on the QEG and we hope to have some good data to share soon.

      Delete
    2. Ya but why is it needed? The original Witts QEG (in the video posted below) there is no exciter coil and yet he achieves OU... he has it self-running with a load and he does not need an exciter coil! May mean nothing... but seems a rather odd discrepancy is all. Perhaps I am just not privy to info that makes it make sense.

      Delete
    3. One must alter the script ever so slightly when plagiarizing else be called a plagiarist.
      Its the end of the Morocco now. The TEAM will be off to another location (vacation) site. Why is this engineer taking a week plus to measure and reveal data.

      Delete
  10. For those who want to see what I mean, here is the video I referred to in which the machine is shown in detail all round. :)
    http://www.youtube.com/watch?v=-Ztt3R4Bu_0

    ReplyDelete
  11. https://www.youtube.com/watch?v=mHW6b1aFPfU

    ReplyDelete
    Replies
    1. Go to peswiki . com to see all the updates on Yildiz.

      Delete
  12. Please listen. That us not an excitor coil. Tesla used his generator for a high voltage source to operate his spark gap that drove his "tesla coil" for the wireless transmission of cold "radiant energy" . It is not needed for producing over unity in this device. I already posted an explanation about the unbalanced tank cicuit. You need way way way more capacitance!

    ReplyDelete
  13. This 24-Port 10/100 transition is a high end auto-sensing transition of which immediately works out a deal in between 10Base-T in addition to 100Base-TX network speeds.
    For more detail: http://www.dueltek.com.au/collections/unmanaged-network-switches/products/24-port-10-100-rack-mount-switch

    ReplyDelete
  14. fake very big scam bastards

    ReplyDelete
  15. Lockable Patch Leads are ideal for guarding your own system gear from unauthorized gain access to or unanticipated disconnections. Utilized all over the world to help safeguarded information places in motels, colleges as well as nursing homes - Could you afford not to ever possess this amount of security?
    For more detail: http://www.dueltek.com.au/pages/ethernet-cables

    ReplyDelete

SITS blog is a venue where Data we come across can be shared with all of you. If we look past personal bias, and distill the Absolute Data within each post, our natural intuition will assemble these nuggets together and reveal a greater truth.

We do not know what that truth is yet of course. We are discovering that together as a whole by sharing and discussing our unique perspective. Share your thoughts and we will all come to a greater understanding as one.

Support Stillness in the Storm